.

.

SM852B Testador de rotação trifásica, 20Hz400Hz Medidor de rotação trifásica digital portátil e ampla faixa para testes de eletricidade com campainha AC 60600V

SM852B Testador de rotação trifásica, 20Hz400Hz Medidor de rotação trifásica digital portátil e ampla

€ 5.29

Número
In stock

Especificação : Item Tipo : Rota de 3 fase Testermateriais : Absmaodel : SM852 BWWORKING Tensão : 60 ~ 600 V (corrente alternada em 3 fase) Objetivo : Medição de corrente alternada em 3 fase MAXIMUM ATRANÇO DA TOLAÇÃO : 20 HZ ~ 400 HZCONTIMOUS/MIN (tensão de pulso 4000v) Frequência de frequência : 20 HZ ~ 400 HZCONTRATIVO (Volso de tensão 4000 V) Tempo : Não mais que 60 minutos a 200 V ACV, não mais que 4 minutos a 600 V Acvhow para usar : conecte a sonda de teste deste instrumento ao fio a ser testado (não pode ser comprimido diretamente à mão), que pode ser uma extremidade de fio Para evitar choques elétricos. Para a conveniência dos usuários, existe um clipe de teste especial nos acessórios de instrumentos. Insira o clipe de teste na sonda de metal do chumbo de teste e aperte -o. Convenientemente o prenda em qualquer lugar para medição). Neste momento, o medidor indicará o estado da fase aberta e a sequência com base na fase do diodo emissor de luz (LED) e na buzinadora1. LED para verificação de fase aberta : três LEDs laranja, indicando a fase U, a fase V e a fase W, respectivamente. LED para verificação da sequência de fases : um LED vermelho e um LED verde, respectivamente, 3. Desenhe a correia : coloque -o no pulso para impedir que o instrumento escorregue da mão. LEITO DE TESTE : O vermelho corresponde à fase U (R) (L1, R); amarelo corresponde à fase V (y) (L2, S); Green corresponde à fase W (B) (L3, T) Lista de pacotes : 1 x 3 Tester de rotação de fase3 x clip1 x manual1 x saco de pano portátil.

Dados do produto

Item Type:
3 Phase Rotation Tester
Material:
ABS
Maodel:
SM852B
Working Voltage:
60~600V (3 phase alternating current)
Purpose:
3 phase alternating current measurement
Maximum Withstand Voltage:
2000v/min (pulse voltage 4000v)
Measurable Frequency Range:
20Hz~400Hz
Continuous Use Time:
no more than 60 minutes at 200V ACV, no more than 4 minutes at 600V ACV
How to Use:
Connect the test probe of this instrument to the wire to be tested (cannot be pinched directly by hand), which can be a wire end, socket or the middle part of the phase wire (when measuring in the middle part of the phase wire, the insulation layer of the wire needs to be stripped Go, the wire core inside can be measured. At this time, pay special attention to to prevent electric shock. For the convenience of users, there is a special test clip in the instrument accessories. Insert the test clip on the metal probe of the test lead and tighten it. Conveniently clip it anywhere for measurement). At this time, the meter will indicate the state of the open phase and the sequence based on the phase of the light emitting diode (LED) and the buzzer:
1. LED for open phase check:
three orange LEDs, indicating U phase, V phase and W phase respectively.
2. LED for phase sequence check:
one red LED and one green LED respectively
3. Draw strap:
put it on the wrist to prevent the instrument from slipping off the hand.
4. Test lead.:
5. Test lead:
red corresponds to U (R) phase (L1, R);
Yellow corresponds to V (Y) phase (L2, S);:
Green corresponds to W (B) phase (L3, T):
Package List:
1 x 3 Phase Rotation Tester:
3 x Clip:
1 x Manual:
1 x Portable Cloth Bag:
Categoria de produto