.

.

YNREMM PV PV PROTECTOR 2P 500VDC Dispositivo de chave SPD Sistema de energia solar Sistema de energia solar Combinador Caixa a laser marcação

YNREMM PV PV PROTECTOR 2P 500VDC Dispositivo de chave SPD Sistema de energia solar Sistema de

€ 2.67

Número
In stock

Disjuntores Especificação do circuito : Sistema de energia solar Shy3-PV.Product Descrição : 1. Conecte o dispositivo de proteção de plugue de estilo/saída. O coler da janela visível mostra o status de operação. Proteção dupla de excesso de calor e excesso de corrente. Ter o acessório da interface de sinalização remota, pode ser controle remoto remoto. Instruções de instalação : 1. antes da instalação. Você deve cortar a fonte de alimentação. Não opere no estado carregado. Sugerimos que um fusível ou disjuntor automático deve ser conectado em série antes do módulo à prova de raios. Na instalação, conecte-se ao diagrama de instalação, conforme mostrado no diagrama, "+" representa o fio do ânodo "-" Pepresenta o fio do cátodo, o PE representa o fio de aterramento, a conexão errada não é permitida. Após o término da instalação, ligue o Swich do disjuntor automático (ou fusível), para verificar se o estado de trabalho não é normal. Após a conclusão da instalação, insira o módulo corretamente e verifique se o módulo à prova de raios funciona normalmente ou não. Vermelho ou o terminal de sinalização remota emite o sinal do alarme, isso significa que o módulo à prova de raios tem a falha, você deve repará-lo ou alterá-lo no tempo. O módulo paralelo à prova de raios de energia deve ser instalado em paralelo, o fio deve ser curto, grosso e reto, conectado de forma firme e confiável.Main parâmetros técnicos : Nomeseries No.Speci-Fications Nominal Capacidade O fluxo (KA 8/20 S) Capacidade de fluxo máxima Lanx (KA8/20 S) Nível de proteção (KV) Tempo de resposta (NS) A coltagem classificada (VDC) continua a trabalhar na corrente de vazamento de tensão (VDC) 0,75 U 1m A (a) Temperatura de trabalho (° C) 500 VDC Llghtning CHLPRND1-C/40236m2m2m20402.

Dados do produto

SHY3-PV Solar power system.:
Product Description:
1. Plug in/out style surge protecive device.:
2. THe coler of visible window shows operating status.:
3. Double protection of over-heat and over-current.:
4. Have the accessory of remots signaling interface,could be remote remote control.:
Installation instructions:
1.Before installing. you must cut off the power supply. don't operate in the charged state.:
2. We suggest a fuse or automatic circuit breaker should be connected in series before the lightningproof module.:
3. In installing, Please connect with the installation diagram, as shown in diagram,+represents the anode wire,- Pepresents the cathode wire, PE represents the earthing wire, the wrong connection is unallowable. After the installtion is finished, turn on the swich of automatic circuit breaker(or fuse), to check whether the working state is normal ot not.:
4. After the installation is completed, insert the module properly, and check whether the lightningproof module works normally or not.:
5.In the period or using the lightningproof module, inspect, test and view the faultdisplay window state regularly, when the fault display window is red or the remote-signalling terminal outputs the alarm signal, this means the lightningproof module has the fault, you shall repair or change it in time.:
6. The parallel power lightningproof module shall be installed in parallel, the wire shall be short, thick and straight, connected firmly and reliably.:
Main Technical Parameters:
Name:
Series No.:
Speci-fications:
Nominal capacity the flow In(KA 8/20s):
Maximum flow capacity lanx(KA8/20s):
Protection level(KV):
Response time(ns):
Rated coltage(VDC):
Continue to work voltage(VDC):
Leakage current 0.75U 1mA(A):
Working temperature:
(°c):
500V:
DC llghtning protection chlp:
RND1-c/40:
236mm:
20:
40:
2.2:
25 :
Categoria de produto